Jump to content

Leaky Lever Filler Where to Start


loganrah

Recommended Posts

I have a lovely little vintage Wahl ring top gold filled lever filler I picked up from Greg Minuskin a while ago (photo from Greg's website bellow). Unfortunately I am having some trouble with the pen: it floods and drips onto the page almost instantly when I start using it. I can sometimes get a line or two before it does so, but it almost invariably does so after that. 

At first I thought the issue was just hand heat causing air to expand and force ink out of the pen (which seems more likely given its tiny size). However, I don't think this is the issue since holding the pen upright in my hand for several minutes to heat it up and equalise air pressure does not help the issue. 


So I suspect there is some other issue with the pen: perhaps the feed is not properly set or there is an air leak somewhere? I live in Australia where it is 38c/100f today and I have carried this pen in my pocket so it is possible that heat has loosened something somewhere. 

What I would most like to know is how I should go about diagnosing the problem. The section seems to be quite tightly screwed in, I cannot remove it with reasonable hand force and I'm nervous about applying too much force with a vintage pen like this. 

 

I would prefer not to have to send it off for repair if I can fix the problem myself, but I will do so if I have to since in its current state it is basically unusable. 

Mods: I've copied this post over from the Wahl-Eversharp forum since I wasn't getting any response there, I hope this is ok.
 

rs=w:1280

Link to comment
Share on other sites

  • Replies 6
  • Created
  • Last Reply

Top Posters In This Topic

  • Ron Z

    2

  • FredRydr

    2

  • loganrah

    2

  • como

    1

Top Posters In This Topic

To eliminate air ingress, the first and simplest line of inquiry is the sac, either its point of attachment to the section or the sac itself.  You could reinstall the existing sac with fresh shellac on the cleaned section nipple, but if you already have new sacs, I would go straight to replacement.  

Link to comment
Share on other sites

If the pen is leaking and hadn't before now, a pen mechanic will go straight for replacing the sac.  Even a new sac can have flaws that cause the pen to flood, so we replace them too.  FWIW, I never reuse a sac...

spacer.png
Visit Main Street Pens
A full service pen shop providing professional, thoughtful vintage pen repair...

Please use email, not a PM for repair and pen purchase inquiries.

Link to comment
Share on other sites

Ok, so assuming I do have to replace the sac, any ideas on how to safely remove the section? I don't want to break anything.

Link to comment
Share on other sites

Start with this tool: Pen Repair (now in its 4th Edition) by Jim Marshall and Laurence Oldfield

 

spacer.png

 

You need a dry heat source and a gentle hand.  Prior experience is a big plus when it comes to a valuable or cherished pen.

Link to comment
Share on other sites

Working on an expensive pen with zero prior experience:

 

The positive: you can really feel the adrenaline going.

The negative: you get some experience in the end but no pen.

 

That’s a great book btw, Pen Repair.

Link to comment
Share on other sites

The sections on metal pens like this can be really tough to get out. As in really tough because the hard rubber cold flows to conform to the shape of the threads inside the barrel.  Heat is needed, in this case you can get it pretty warm and the barrel will conduct the heat, so I suggest a rubber grippy pad (made of the rubber mesh shelf liner) to grip the pen so that you don't burn your hands, and then try to unscrew the section.  Use section pliers, or fuel line hose slipped over the section to keep from marring it with a pair of pliers.  Don't let the jaws of metal pliers come in contact with the section.

 

An article about making your own tools can be found here.

 

The advice to have someone do the work isn't a bad one if you have never repaired a pen, because these usually are a pain to get open.

spacer.png
Visit Main Street Pens
A full service pen shop providing professional, thoughtful vintage pen repair...

Please use email, not a PM for repair and pen purchase inquiries.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Most Contributions

    1. amberleadavis
      amberleadavis
      43844
    2. PAKMAN
      PAKMAN
      33501
    3. Ghost Plane
      Ghost Plane
      28220
    4. inkstainedruth
      inkstainedruth
      26627
    5. jar
      jar
      26101
  • Upcoming Events

  • Blog Comments

    • Shanghai Knife Dude
      I have the Sailor Naginata and some fancy blade nibs coming after 2022 by a number of new workshop from China.  With all my respect, IMHO, they are all (bleep) in doing chinese characters.  Go use a bush, or at least a bush pen. 
    • A Smug Dill
      It is the reason why I'm so keen on the idea of a personal library — of pens, nibs, inks, paper products, etc. — and spent so much money, as well as time and effort, to “build” it for myself (because I can't simply remember everything, especially as I'm getting older fast) and my wife, so that we can “know”; and, instead of just disposing of what displeased us, or even just not good enough to be “given the time of day” against competition from >500 other pens and >500 other inks for our at
    • adamselene
      Agreed.  And I think it’s good to be aware of this early on and think about at the point of buying rather than rationalizing a purchase..
    • A Smug Dill
      Alas, one cannot know “good” without some idea of “bad” against which to contrast; and, as one of my former bosses (back when I was in my twenties) used to say, “on the scale of good to bad…”, it's a spectrum, not a dichotomy. Whereas subjectively acceptable (or tolerable) and unacceptable may well be a dichotomy to someone, and finding whether the threshold or cusp between them lies takes experiencing many degrees of less-than-ideal, especially if the decision is somehow influenced by factors o
    • adamselene
      I got my first real fountain pen on my 60th birthday and many hundreds of pens later I’ve often thought of what I should’ve known in the beginning. I have many pens, the majority of which have some objectionable feature. If they are too delicate, or can’t be posted, or they are too precious to face losing , still they are users, but only in very limited environments..  I have a big disliking for pens that have the cap jump into the air and fly off. I object to Pens that dry out, or leave blobs o
  • Chatbox

    You don't have permission to chat.
    Load More
  • Files






×
×
  • Create New...