Jump to content

sheldon1936

Recommended Posts

I recently spent a few hours working on my good ole' ebonite Noodlers Konrad. I hadn't used this pen for quite a while and wanted to spice things up a bit. The changes I made (and highly recommend) are as follows:

 

1) the "easy my flex" mod, were you grind a portion off the sides of the nib as seen in the picture.

 

2) I doubled the depth/width of the feed channel, which managed to eliminate almost all railroading except on very aggressive downstrokes. and

 

3) I reground the tip to an XXXF needlepoint. I don't know how to measure the actual degree of fineness I achieved with this grind, but ill tell you it is so sharp that I may just use it to sew some new underpants.

 

I don't by any means consider myself an experienced nib-alter-er-er, but it wasn't too difficult to shave the sides and smooth the tip with 8000, 12000 and 16000 grit polishing sandpaper.

 

Anyways, here are some pictures of my work (and first attempt calligraphy); please comment if you have any questions, suggestions or have tried the same thing during your nib-related adventures. Enjoy.

 

post-112010-0-61923000-1395791818_thumb.jpg

 

post-112010-0-51984700-1395791838_thumb.jpg

Link to comment
Share on other sites

  • Replies 34
  • Created
  • Last Reply

Top Posters In This Topic

  • sheldon1936

    7

  • Fabienne

    3

  • jelly

    3

  • linearM

    1

Top Posters In This Topic

Posted Images

That is really cool. Have you thought about doing the ease my flex mod to make the nib easier to flex? A XXXF nib with (near) full flex in such a cheap pen would be amazing.

Edited by discopig
Link to comment
Share on other sites

That is really cool. Have you thought about doing the ease my flex mod to make the nib easier to flex? A XXXF nib with (near) full flex in such a cheap pen would be amazing.

Yeah, that was the first thing I did actually, and after the regrind it takes just a little more effort to flex than most dip nibs (A new gillott 303 was what I compared it to). Its bliss i tell you.

Link to comment
Share on other sites

One place you might go to find the width of your line is Richards Pens. Look for his Stroke Width Chart.

 

You got some very good results with your efforts.

Link to comment
Share on other sites

Very nice! What method did you use to deepen the feed channel? Razor blade or something else?

I scraped the edges down with a razor sharp swiss army knife, and removed the one set of fins near the tip. It seemed to encourage ink to flow to the tines even when they're spread quite wide. It doesn't write too wet however when doing normal cursive so it still performs well on more feathering-prone paper, despite the added scratchiness.

Link to comment
Share on other sites

I am going to have to get out the micromesh and go at the tip of my Ahab, too. I like it but it's a bit too broad and to get it down to needle point would be a dream. You just used the 8000-12000-16000 to polish (grind) down either side of the tip of the nib? Did it take long (as the nib it steel).


 It's for Yew!bastardchildlil.jpg

 

Link to comment
Share on other sites

I am definitely trying this out with my Ahab. The beauty of Noodlers pens is that it's cheap enough that reward after a successful modification outweighs the loss in case of failure.

Link to comment
Share on other sites

I attached small ~1cm Dremel fine sanding drum to a high rpm drill and carefully ground down the sides and bottom of the nib. I taped the nib tines together so that they wouldn't slip over one another, allowing me to get the sharp needlepoint nib.

 

Also I compared the hairlines I can achieve with this nib to a micro pen with a 0.2mm tip, and this nib was a little finer. I'm tempted to do this to some other cheap nibs sitting in the old pen box, I'll post the technique I use when I do so.

Link to comment
Share on other sites

That is terrifyingly sharp and fine, well done! Do you think the technique would be much different if I were to try this on a gold (14ct) nib?

Link to comment
Share on other sites

That is terrifyingly sharp and fine, well done! Do you think the technique would be much different if I were to try this on a gold (14ct) nib?

I can imagine a gold nib would wear down faster than the steel I used. And with the tools I used, even steel wore down quite quickly. Maybe try it on a cheaper more robust steel nib before risking the safety of a more expensive 14k gold one first. I also have a vintage 14k Pick Pen Co. pen that flexes easily but writes too broad for my taste. hmmmmm...

Link to comment
Share on other sites

I personally would recommend some sort of spinning power tool just to save time, but it would probably be possible by hand if you are patient. Just remember to check your work under pristine lighting conditions and if possible a powerful magnifying glass. You don't want one razor sharp tine to end up even a fraction longer than the other; that would make upstrokes a scratchy mess. And remember that whats gone is gone...

Link to comment
Share on other sites

Oh man! I love threads like this! I'm working on a low cost option for terrific flex right now, and it would really help me out if you could take a few minutes to give me some insight on your flex pen thoughts. That's a link to a survey that will help me guide my parameters. I think you'll all like the results once I'm done.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Most Contributions

    1. amberleadavis
      amberleadavis
      43844
    2. PAKMAN
      PAKMAN
      33494
    3. Ghost Plane
      Ghost Plane
      28220
    4. inkstainedruth
      inkstainedruth
      26624
    5. jar
      jar
      26101
  • Upcoming Events

  • Blog Comments

    • Shanghai Knife Dude
      I have the Sailor Naginata and some fancy blade nibs coming after 2022 by a number of new workshop from China.  With all my respect, IMHO, they are all (bleep) in doing chinese characters.  Go use a bush, or at least a bush pen. 
    • A Smug Dill
      It is the reason why I'm so keen on the idea of a personal library — of pens, nibs, inks, paper products, etc. — and spent so much money, as well as time and effort, to “build” it for myself (because I can't simply remember everything, especially as I'm getting older fast) and my wife, so that we can “know”; and, instead of just disposing of what displeased us, or even just not good enough to be “given the time of day” against competition from >500 other pens and >500 other inks for our at
    • adamselene
      Agreed.  And I think it’s good to be aware of this early on and think about at the point of buying rather than rationalizing a purchase..
    • A Smug Dill
      Alas, one cannot know “good” without some idea of “bad” against which to contrast; and, as one of my former bosses (back when I was in my twenties) used to say, “on the scale of good to bad…”, it's a spectrum, not a dichotomy. Whereas subjectively acceptable (or tolerable) and unacceptable may well be a dichotomy to someone, and finding whether the threshold or cusp between them lies takes experiencing many degrees of less-than-ideal, especially if the decision is somehow influenced by factors o
    • adamselene
      I got my first real fountain pen on my 60th birthday and many hundreds of pens later I’ve often thought of what I should’ve known in the beginning. I have many pens, the majority of which have some objectionable feature. If they are too delicate, or can’t be posted, or they are too precious to face losing , still they are users, but only in very limited environments..  I have a big disliking for pens that have the cap jump into the air and fly off. I object to Pens that dry out, or leave blobs o
  • Chatbox

    You don't have permission to chat.
    Load More
  • Files






×
×
  • Create New...