Jump to content

FPN Admin Column

  • entries
    27
  • comments
    665
  • views
    333,826

Contributors to this blog

  • Admin 23
  • wimg 4

Shipping Well On Its Way, And Some Pen Tips ....


wimg

13,702 views

Dearest members of the digital fountain pen nut house,

 

It has been several weeks already since shipping started, and many of the FPN LE Passportos in Chrome trim and in Gold Coloured trim have been collected by DHL in the beautiful town of Florence in Italy and have found their way to their respective new owners. For a few pictures of these pens, you can check here: http://www.fountainp...to-on-the-road/, or obviously in the FPN Pens forum. The Modello-Ts and Etrurias are expected to start shipping this week.

 

 

A few useful, we hope, tips follow here, based on questions we received so far.

 

 

1. Removal/Exchange of Passaporto nibs.

We've had a few questions regarding exchanging the nib units on the Passaportos, as those proved rather hard to remove, and we now have nib exchange / removal instructions which work very well, thanks to inkspot and Maja, who simultaneously and independently discovered the way to do this!

 

The nib itself can be removed and replaced quite easily, all you need is something to increase your grip, like a piece of flexible rubber matting, and if you have a good grip with your fingers, it may even be possible to do this just with one's bare hands. I gave it a go with a thin, rubber, flexible mouse mat, and it worked like a charm!

 

Essentially, the trick is to grip the sides of the nib, by the shoulders, with the rubber mat in my case, and just pull. You may have to wriggle a little, but the nib will come out quite easily that way, leaving the feed in place. I didn't have to wriggle, BTW, I could just pull it out quite easily in a straight line.

 

Next pull the nib from the nib unit you'd like to install, and insert that nib by pushing it up over the feed, all the way as far as it will go, again using the rubber matting for increased grip (and to avoid ending up with a nib point in one's skin :D). Just check that it is seated properly, tight to the feed, and adjust if necessary.

 

That's all, easy-peasy. Took less than a minute to do. And because it is a tight fit, I reckon it is almost impossible to get it wrong. :D

 

 

2. Shipping info and tracking numbers.

 

We send out emails with tracking numbers and a link to the DHL site in order to follow the shipping trail. Essentially, these emails contain a personalized note, with the tracking number for your order, and a url, and they are sent from info@fountainpennetwork.com, which is a no-reply email address created for exactly this type of message.

 

If messages from FPN end up in your regular mailbox, these should too, but if they don't, better check your spam folder.

 

 

3. Passaporto nib sizes.

 

The Passaporto F and M nibs tend to be a little on the narrow side compared to "regular" European nib sizes, more like Japanese nibs, maybe slightly bigger. Furthermore, as Etruria S.r.l. indicated when asked, there is some variation in nib width, as is the case with all nibs anyway. However, from all accounts they do write very, very smoothly, and quite impressively so based on comments received so far.

 

Having said this, the 1.1 italic nibs are true to size, they really lay down a 1.1 mm wide vertical stroke. This is typical for all Stipula italic nibs: the line laid down is indeed as wide as it says in the descriptive nib name :D.

 

 

4. Initial starting problems / rinsing and priming a nib and feed.

 

New pens, especially hand made ones like the Stipulas, may have some residual grease in the feed etc. when coming straight from the box, and as a result may start with difficulty initially.

 

The best thing to do obviously is to remove any residu, and this can be done quite easily, by rinsing the nib and feed with a soapy solution. A soapy solution is essentially a smallish glass filled with some water and one to two drops of a neutral dishwashing liquid, stirred, not shaken :D. A neutral dishwashing liquid is one without additives like perfumes and skin softeners etc. Generally, the cheapest available will do very nicely.

 

Rinsing the nib and feed can be done most easily when the pen is a piston filler, or in case of Passaporto or Modello-T, with a converter, international size. Just insert the converter in the pen, and in case of the Passaporto it doesn't matter that the size of the converter is too big to screw on the barrel, because we will not do that anyway. Next fill the pen through the nib with the soapy solution and squirt the solution out again, into the sink or into another glass. Repeat this a few (2-4) times, remove converter if appropriate, and dry the nid/feed/pen a little, with a soft cloth or tissue.

 

Now fill the pen with a few drops of a simple ink, which flows well and has good lubrication characteristics. The amount roughly contained in a single short international cartridge is ample for this purpose. A simple ink as described, is f.e. Waterman Blue Black, Waterman Florida Blue, or Waterman South Seas Blue. I use such an ink to, what I have called several years ago, "priming the feed", i.e., somehow get the ink channels and feed itself thoroughly soaked in a good ink, thereby "priming" it to be used with any other, potentially more complex ink thereafter. The big advantage is that an ink as mentioned will make the initial writing process a pleasant one, whereas a complex, heavily saturated ink will potentially make this an arduous task. Complex inks often take several fills to prime a nib, and during that period one may experience a lot of skipping and slow or bad starting. Based on my own tests this proved to be anything from 2 to 15 cartridges full of ink (that is without rinsing the nib and feed as well). Priming a feed with a well behaved, simple ink avoids this, and sets the pen up for a more complex ink thereafter.

 

 

5. Increasing ink flow / making the nibs write wetter.

 

The Passaporto nibs are medium wet writers, with rather tightly spaced tines, writing relatively thin lines as a result. Increasing ink flow is possible, but this needs to be done properly in order not to change nib geometry and potentially cause problems, like ink pooling.

 

The best way to increase ink flow, is to use a brass feeler gauge, thickness 0.002 " or 0.05 mm. By lack of this, a piece of a thin transparant overhead sheet may be used as well. Just wriggle this between the nib tines and tipping, if need be by carefully pushing one of the tines down or up a tiny bit with a finger nail, and slowly but carefully pulling the feeler gauge or piece of sheeting between the tines and tipping ends, essentially carefully flossing the nib if you like.

 

Repeat this process until ink flow is as expected. IOW between attempts you need to try if the result is satisfactory. If it appears that the feeler gauge is too thin to achieve the desired effect, you may want to try a 0.004 " or 0.10 mm gauge.

 

In case you don't have or can't find a brass feeler gauge, you may try a stainless steel one, just be very careful, as stainless steel is much tougher and harder than brass, and may more easily damage nib tipping, or scratch the nib.

 

 

6. Reporting problems with your pen(s)

 

If e.g., skipping cannot be fixed by rinsing the pen, or anything else for that matter, do report this to undersigned, by means of a PM, or preferably an email (check my profile to send an email), and we will try to answer as quickly as possible, and/or follow this up with Etruria S.r.l. where and if needed.

 

 

So far this update, and a few tips. If you do have tips yourself, please do post them, they are always appreciated.

 

Warm regards, Wim

On behalf of the FPN Admin Team

49 Comments


Recommended Comments



Wim, I can't thank you enough.

 

My pens arrived today 1/4/2012. It's my birthday! What an amazing birthday gift!

 

I got the Passaporto and the Azzurrite jewel clip / silver trim Modello T. I opened my package with family at my birthday dinner.

 

Everyone loved the cute little Passaporto. All were impressed with the beauty of the Modello T.

 

I love both pens. I just took my Modello T for a test drive just now filled with Waterman Florida Blue ink. It's writes like a dream and feels so good in the hand. It makes beautiful lines and makes my writing pretty actually. Lol!

 

I had completely forgotten about these pens until I got the shipping notice by email a few days ago. I'm in California. That was fast.

 

This has been a great birthday and it's partially because of you and Stipula.

 

Thank You So Much!!!

Simcha

Link to comment

:) Hi Wim, just wondering if you have heard back from Stipula on the screw-out/screw-in feature of the Passaporto pens yet?:( Or did you post the response in another blog or thread?:unsure: Or am I really clueless and missed it in this one?:embarrassed_smile:

Lou

 

 

Link to comment

Hi Lou,

Only that they use specilized tools to do so, and that the method described above is a good one.

They would still investigate whether there were any other possibilities, but I haven't heard anything yet. I'll ask again.

Warm regards, Wim

Link to comment

Hi,

 

It's 8th Jan, and I still haven't received any mailing notification (I checked my spam) nor the pen itself. Should I be concerned?

Link to comment

I concur with metwin1 - I, too, have heard nothing on the status of my Modello T. Any news to share with us?

Link to comment

I hope to get another update today - last week was a very short week in Italy, due to public holidays.

 

Warm regards, Wim

Link to comment

Hi Lou,<BR><BR>Only that they use specilized tools to do so, and that the method described above is a good one. <BR><BR>They would still investigate whether there were any other possibilities, but I haven't heard anything yet. I'll ask again.<BR><BR>Warm regards, Wim

 

 

Thanks for the response. I am still very pleased with the performance of my Passaporto. Maybe I'll feel brave enough to try the 'pull out the nib' method, probably over cautiousness is robbing me of the experience of using an Italic Nib, but for now I'm satisfied with the factory installed medium one.

Thanks again for re-checking with Stipula, and now that the Christmas rush is passed they'll have more time to fully reply?

Lou

Link to comment

Well, it looks like that is the preferred method now with the extra O-ring installed behind the nib unit, unless you have special tools ot do this. You'll have to try and pull just the nib itself, gripping it by the sides with something that will increase your grip, like some flexible rubber matting (flexible rubber mouse mat, or in your case, possibly a piece of inner tube from a bicycle :D).

 

HTH, warm regards, Wim

Link to comment

Hi Wim,

 

I gather that I shouldn't panic about not having received any notification of my pen and nib shipping? I suppose I also should probably not just stare anxiously at the mailbox. . .

 

ciao,

Gretchen

Link to comment

Hi Wim,I gather that I shouldn't panic about not having received any notification of my pen and nib shipping? I suppose I also should probably not just stare anxiously at the mailbox. . . ciao,Gretchen

 

 

Of course not. Did not your mum teach you that it is rude to stare...??

Now you just sit and wait till the nice DHL man brings you your package.

 

(going of to play with his pens.....)

 

 

D.ick

 

(feeling naughty now)

Link to comment

LOL as well you should! Playing with your Stipulas right in front of me while I continue to try to be patient? Tut tut -- cruel, you are cruel!

 

Ciao

Gretchen

Link to comment

Hi Gretchen,

 

Yes, D.ick can be cruel :D.

 

As to your pen and nib: no need to worry, the moment we get a shipping update with your order listed as having been shipped, you will get a shipping info email, with tracking number. It will be sent from info@fountainpennetwork.com, with FPN Pen Shipping Info as a title.

 

HTH, warm regards, Wim

Link to comment

Hello Everyone,

 

I just received my DHL package and greedily ripped it open to have a first look at my Modello T. I tried to fit the converter into the pen, but it does not want to stick. Does anyone know if the "O" ring at the base of the nib section has to be removed first for the converter to seat properly???

 

Hoping that someone can enlighten me quickly so that I can ink it up.

 

Thanks,

 

Peter

Link to comment

Hello Everyone,I just received my DHL package and greedily ripped it open to have a first look at my Modello T. I tried to fit the converter into the pen, but it does not want to stick. Does anyone know if the "O" ring at the base of the nib section has to be removed first for the converter to seat properly???Hoping that someone can enlighten me quickly so that I can ink it up.Thanks,Peter

 

 

OK, I just looked around a little more closely and found that there already was a thread on this issue. I took the posted advice and pushed, prodded and wiggled until indeed the converter finally seated properly, and, sure enough, as others had reported, after the first time, the converter removes and reseats quite easily. Hurray :clap1:

Link to comment

Hello Everyone,

 

I just received my DHL package and greedily ripped it open to have a first look at my Modello T. I tried to fit the converter into the pen, but it does not want to stick. Does anyone know if the "O" ring at the base of the nib section has to be removed first for the converter to seat properly???

 

Hoping that someone can enlighten me quickly so that I can ink it up.

 

Thanks,

 

Peter

Hi Peter, nothing needs to be removed at all, and certainly shouldn't be. It is a tight fit initially, see peninsular's remark above.

 

HTH, warm regards, Wim

Link to comment

I'm just checking to see if there are still pens waiting to be shipped? I haven't gotten my notification yet and I wanted to know if I should worry yet! Thanks!

Link to comment

I just received my Azurite Etruria Vermeil and boy is it a beauty! I am having a heck of a time getting this thing to write. I've gone through the flushing several times (both water and load/reload of SSB ink. It either skips, pools or just writes REALLY broad (on par with my broad pelikan...not what I thought I should see from a fine nib?). The cap also catches screwing on/off.

 

Beautiful pen but I'm so disappointed its not really useable (and I don't want to damage it). :crybaby: any advice??

Link to comment

Please contact me backchannel. I really need to see a few pics of the nib.

 

Warm regards, Wim

Link to comment

I did Wim, thx..just figured I'd see if anyone else was having issues. :)

Link to comment

Nothing that a good flush and slight nib adjustment as indicated in the FPN Pens forum couldn't fix, with the exception of one piston seal rupture, which will be fixed in Italy.

 

Warm regards, Wim

Link to comment

Has everyone received their pens yet? I'm just wondering if they had manufactured the last batch yet, I have no received mine. :(

Link to comment

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now





×
×
  • Create New...