Jump to content

Shepherds Hook Pressure Bar Placement(Sheaffer Balance)


RayCornett

Recommended Posts

I have replaced lots of pressure bars in Sheaffer Balances but a couple of years ago I obtained one with what I have since discovered is called a Shepherds hook pressure bar.

The original was horribly corroded so I removed it hoping to perhaps clean it up but the corrosion was too far advanced and the small bit that makes it not just a J bar broke off.

I recently obtained a NOS replacement and sought advice on how to place it. I was told to get the bar started into the slot in the end of the barrel then lift that tab with a strong dental tool and lift that "tab" into the slot. Well, that tab seems to be caught on the lip of the slot and no dental tool I have is moving it.

I am open to suggestions.

post-125250-0-76173700-1570730944.jpg

Edited by RayCornett
Link to comment
Share on other sites

  • Replies 4
  • Created
  • Last Reply

Top Posters In This Topic

  • RayCornett

    3

  • Ron Z

    2

Popular Days

Top Posters In This Topic

Posted Images

Usually called, and listed as, a J pressure bar - never heard the phrase shepherds hook used.

 

These can be a pain in the tush to remove. Catch an edge with a dental tool and push the tool forwards while pressing it towards the center. This will bend the metal and let it fall out. If that doesn't work, try an alligator hemostat. They reach down inside with the jaws at the front, and you could grab the sides, and turn while pulling. Widgetsupply.com sells them at a reasonable price, Not top grade, but they last a reasonable length of time, even with some abuse. The 3.5" one is plenty long, and what I use most of the time.

spacer.png
Visit Main Street Pens
A full service pen shop providing professional, thoughtful vintage pen repair...

Please use email, not a PM for repair and pen purchase inquiries.

Link to comment
Share on other sites

Usually called, and listed as, a J pressure bar - never heard the phrase shepherds hook used.

 

These can be a pain in the tush to remove. Catch an edge with a dental tool and push the tool forwards while pressing it towards the center. This will bend the metal and let it fall out. If that doesn't work, try an alligator hemostat. They reach down inside with the jaws at the front, and you could grab the sides, and turn while pulling. Widgetsupply.com sells them at a reasonable price, Not top grade, but they last a reasonable length of time, even with some abuse. The 3.5" one is plenty long, and what I use most of the time.

I have just seen it called Shephers hook on Ebay and by a couple other people. Mainly because of the shape.

 

That tool is definitely one I notice I need and will be getting asap. I think they have them at Harbor Freight down the street. And just to clarify, I am not trying to remove this one. This is the NOS bar that I am putting in. The old one WAS a hassle to get out but apparently it needed to be replaced anyway due to the major corrosion.

post-125250-0-64769100-1570735609_thumb.jpg

Edited by RayCornett
Link to comment
Share on other sites

Sorry - I thought that you were trying to remove the old one. There isn't a slot as such at the end. The end of the barrel is often drilled to a smaller diameter.

 

You may be able to grab the end of the hook with tab with the forceps and pinch it. Sheaffer used a tool with a slot that the hook went into, and something farther up that the end of the bar went into. You could catch the tab, force the assembly down and shove it in, then rotate to line it up properly with the lever. There were a couple of different sizes for the different size J bars. The forceps let you grab the sides of the hook to rotate the J bar so that the lever rides in the exact middle. If it's off, the lever tends to push the J bar to the side.

spacer.png
Visit Main Street Pens
A full service pen shop providing professional, thoughtful vintage pen repair...

Please use email, not a PM for repair and pen purchase inquiries.

Link to comment
Share on other sites

Sorry - I thought that you were trying to remove the old one. There isn't a slot as such at the end. The end of the barrel is often drilled to a smaller diameter.

 

You may be able to grab the end of the hook with tab with the forceps and pinch it. Sheaffer used a tool with a slot that the hook went into, and something farther up that the end of the bar went into. You could catch the tab, force the assembly down and shove it in, then rotate to line it up properly with the lever. There were a couple of different sizes for the different size J bars. The forceps let you grab the sides of the hook to rotate the J bar so that the lever rides in the exact middle. If it's off, the lever tends to push the J bar to the side.

Just using slot as that is what the first person who talked with me about this used. I did think it was an odd term for what is actually there.

 

I'll have to back it out to be able to pinch it. As it is right now that tab is nearly straight out sideways instead of at a downward angle. Shouldn't be a problem but as it is, the lever and all are lined up fine and the lever operates as expected. The little bit that protrudes from the back of the bar is centered perfectly. I could probably technically leave it as is and it would work fine. I am just picky because I know it's not as it should be :)

Edited by RayCornett
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Most Contributions

    1. amberleadavis
      amberleadavis
      43844
    2. PAKMAN
      PAKMAN
      33497
    3. Ghost Plane
      Ghost Plane
      28220
    4. inkstainedruth
      inkstainedruth
      26627
    5. jar
      jar
      26101
  • Upcoming Events

  • Blog Comments

    • Shanghai Knife Dude
      I have the Sailor Naginata and some fancy blade nibs coming after 2022 by a number of new workshop from China.  With all my respect, IMHO, they are all (bleep) in doing chinese characters.  Go use a bush, or at least a bush pen. 
    • A Smug Dill
      It is the reason why I'm so keen on the idea of a personal library — of pens, nibs, inks, paper products, etc. — and spent so much money, as well as time and effort, to “build” it for myself (because I can't simply remember everything, especially as I'm getting older fast) and my wife, so that we can “know”; and, instead of just disposing of what displeased us, or even just not good enough to be “given the time of day” against competition from >500 other pens and >500 other inks for our at
    • adamselene
      Agreed.  And I think it’s good to be aware of this early on and think about at the point of buying rather than rationalizing a purchase..
    • A Smug Dill
      Alas, one cannot know “good” without some idea of “bad” against which to contrast; and, as one of my former bosses (back when I was in my twenties) used to say, “on the scale of good to bad…”, it's a spectrum, not a dichotomy. Whereas subjectively acceptable (or tolerable) and unacceptable may well be a dichotomy to someone, and finding whether the threshold or cusp between them lies takes experiencing many degrees of less-than-ideal, especially if the decision is somehow influenced by factors o
    • adamselene
      I got my first real fountain pen on my 60th birthday and many hundreds of pens later I’ve often thought of what I should’ve known in the beginning. I have many pens, the majority of which have some objectionable feature. If they are too delicate, or can’t be posted, or they are too precious to face losing , still they are users, but only in very limited environments..  I have a big disliking for pens that have the cap jump into the air and fly off. I object to Pens that dry out, or leave blobs o
  • Chatbox

    You don't have permission to chat.
    Load More
  • Files






×
×
  • Create New...