Jump to content

The Fountain Pen Network uses (functional) cookies. Read the FPN Privacy Policy for more info.  To remove this message, please click here to accept the use of cookies






Photo

Twsbi Eco Dry In A Way?

twsbi eco problem dry

  • Please log in to reply
5 replies to this topic

#1 OTrizy

OTrizy

    Dipped Only

  • Member - Silver

  • Pip
  • 6 posts
  • Flag:

Posted 04 June 2017 - 18:33

I don't think it just me or my Ecos but I have and issue with my eco. I need to prime the feed about every 2-4 pages I write. 

For example first time in the morning I do is to write essays/text in general and after 2 pages my shading ink is not shading anything and is a lot lighter then my letters are missing some parts like T letters the '-' part or something like that then I screw my piston for a little bit so I forced some more ink to my feed and after a while I have the same problem. I know some others have the same issues but did you guys find a solution to this or just try to deal with it. 

 

Btw I write in Rhodia paper with Noodler's Blue-Black Air-Corp. Twsbi Eco M and F nib. 



Sponsored Content

#2 Tasmith

Tasmith

    Uff Da!

  • Member - Gold

  • PipPipPipPipPipPipPipPipPip
  • 1,523 posts
  • Location:Washington, DC metropolitan area
  • Flag:

Posted 04 June 2017 - 19:50

My Eco wrote very dry when new.  Then I flossed the nib with .002" brass shim and that helped a lot with the writing dry issues.



#3 OTrizy

OTrizy

    Dipped Only

  • Member - Silver

  • Pip
  • 6 posts
  • Flag:

Posted 04 June 2017 - 23:16

I maybe have to try that too but I still feel like the feed is the problem here

#4 OilMugs

OilMugs

    Extremely Rare

  • Member - Gold

  • PipPipPipPipPipPip
  • 276 posts

Posted 05 June 2017 - 14:16

Its probably a good moment to point out a source on nib flossing shims that you may already have in your home.

 

Many DVD cases have a security device built into them, often with a bar code over the top. Take a sharp knife and cut into that device and you will find two thin shims which can be used to floss the slit of the nib.



#5 OTrizy

OTrizy

    Dipped Only

  • Member - Silver

  • Pip
  • 6 posts
  • Flag:

Posted 05 June 2017 - 20:52

Oh really? Thank you for the info, now I got to hunt for some DVD cases



#6 ac12

ac12

    Museum Piece

  • Member - Gold

  • PipPipPipPipPipPipPipPipPipPipPip
  • 9,504 posts
  • Location:San Francisco Bay Area, California, USA - SFO
  • Flag:

Posted 06 June 2017 - 06:44

First verify that you have the nib FLAT LEVEL on the paper, so that both tines are touching the paper, not one side lifted. 

  • Hold the pen as you write
  • Then without moving the pen and hand, move your head to look down the length of the pen. 
  • Is the nib level? 
  • If not rotate the pen to level the nib, then test.

If the nib is level, then the nib may be dry.

Very carefully lift the shoulders of the nib a TINY bit, then test the flow, then repeat as needed.

After you are done, check the tip for alignment with a 10x loupe, as lifting the shoulders of the nib can put the tip of the nib out of alignment.

 

Flossing of the nib is to clean the slit of the nib, just like you would floss your teeth.  It is not to wedge it wider.  If you are not careful, you could damage the tipping, or scratch the sides of the slit (on soft gold nibs), when trying to wedge the slit wider.

 

I get my brass sheets to floss the nib from my local hobby shop.  Then cut a piece to a convenient size to use about 2-3cm square.

Then I burnish the edges of the cut piece with the bottom of a stainless steel spoon, to flatten out any burrs.


San Francisco Pen Show - August 23-25, 2019 - Redwood City, California

www.SFPenShow.com






Also tagged with one or more of these keywords: twsbi, eco, problem, dry



Sponsored Content




|